2000 nissan s15 200sx rolling chassis project car

FOR SALE – NISSAN S15 200SX ROLLING CHASSIS PROJECT CAR Selling my Nissan S15 200sx JDM rolling chassis project car as an abandoned project Everything has been kept in storage for quote a few years and it’s time to pass it on to someone who can build the car up There are many unknowns about this car but I am upfront and honest with everything that I do and don’t know Any questions I will try my best to answer to my knowledge Ready to start building into a dedicated track/drift/time attack/rally car Cannot be registered as the VIN/compliance plates were cut off by one of the previous owners Most of the car has been gutted. Ready to be built UP Parts that I had intended on installing are included in the sale As the car and parts have been in storage for many years, some parts have become scratched or damaged and need a clean I have never driven the car or started the engine Being sold AS IS No time wasters please. CHASSIS | - Nissan S15 200sx - Unknown year - JDM model - VIN/compliance plates removed by previous owner - Rolling chassis on S14/S15 stock wheels with bad/temp tyres - Straight body and chassis rails - BUT small damage was taken from passenger rear quarter panel but has not affected the chassis. Please see photos - Front radiator mount / bonnet mount cut off - Front wheel wells cut off - Most nuts & bolts removed - Most of the sound deadening has been removed except in the boot - Rear end/parcel shelf partially blocked off using 5005 aluminium sheet - Rear quarter panels cut out - Rear end cut - Boot floor pan removed - Boot mechanism removed - All electrical wiring removed - Brake lines removed - Fuel lines removed - Always stored under cover in storage garages or sheds. ENGINE & DRIVETRAIN | - Nissan SR20DET 2.0 turbo - Unknown year or kilometers - NOTE: Engine is seated in engine bay on stock engine mounts without being bolted in - Engine cylinder and pistons seem without any cracks or issues - Needs a clean due to storage but appears to be in working order - GKTech SR20 High Performance Engine fan - INCLUDES GKTech eccentric throttle wheel - Stock JDM T28 ball bearing turbo with no compressor shaft play - Stock boost actuator - INCLUDES exhaust dump pipe (not installed) - Clutch: Unknown - Clutch line removed - Clutch needs a clean due to storage but appears to be in working order - Stock S15 6-speed transmission with GKTech solid shifter bush - Stock tail shaft - Stock differential (if I recall diff has been shimmed) - All fluids have been kept in (eg engine oil, transmission oil, diff oil) during storage but recommend inspection and service before attempting to start. SUSPENSION & STEERING | - Hard Race front castor arms - Hard Race steering rack ends (increased steering angle) - Road Safe steering tie rod ends (increased steering angle) - Front: Tien coilovers with front camber adjustment plate - Rear: Tien coilovers - Stock rear arms - Stock sway bars removed (but included in sale) - Extra stock rear arms included - GKTech 15mm wheel spacers. BRAKES | - Stock brake calipers front and rear - Stock brake rotors front and rear. Surface rust due to storage - Stock brake pads front and rear - All brake lines removed - INCLUDES GKTech Brake Master Cylinder Stopper - INCLUDES ABS delete braided brake lines - INCLUDES HEL braided brake lines (front and rear) - INCLUDES HEL hydraulic handbrake brake lines - INCLUDES 420mm carbon fibre hydraulic handbrake and 0.625 bore master cylinder - NOTE hydraulic handbrake and braided brake lines (designed to be INLINE setup) with mounting points drilled into the transmission tunnel. BODY & PANELS | - MISSING FRONT BAR - MISSING FRONT WINDSCREEN - Fiberglass vented bonnet: slightly damaged - Fiberglass front wide body fenders: side indicators filled in - Aftermarket fiberglass side skirts: damaged - Stock doors: gutted, windows and window mechanism removed - Fiberglass 30mm rear wide body fenders: fuel flap filled in - Stock boot with boot mechanisms removed - Aftermarket fiberglass rear bar - Door windows removed - Standard rear quarter windows - Rear window: rear wiper delete applied, glass in decent condition, new seal recommended - Rear boot wing - Rear quarter panels cut.  MISSING PARTS | Parts that are KNOWN to be missing (there could be more): - Front bar - Intercooler / front mount intercooler - Radiator - Front windscreen - Seats & rails - Fuel tank / fuel cell - Fuel lines - ECU - Exhaust system - All wiring was removed but is included in the sale - Interior dash is included but missing centre console ---MOVING THE CAR AND PARTS | - Car is rolling shell - Front wheels, steering rack, suspension are installed - Front brake rotors are installed, brake calipers and pads are removed - Rear wheels, suspension, subframe, diff, axels, brake rotors, callipers and discs installed - Engine is seated in engine bay on stock engine mounts without being bolted in - Transmission and tail shaft are stored outside the car - Car can be pushed and steered by one person into position - All parts and panels can be kept inside the car and ‘wrapped’ and secured using 3-4 ratchet straps - Recommend tow car and car trailer - Recommend tow truck - If required I can assist with arranging for a tow truck quote, or can deliver the car on using a car trailer within a reasonable distance surrounding Melbourne at a negotiated additional cost. Hydraulic Handbrake Details Height: 420mm Hole centres: 112mm x 26mm Master Cylinder Bore: 0.625 Inlet Thread (Front): 3/8 UNF Fine Outlet Thread (Rear): 7/16 UNF Fine Positioning Jack Details 4x wheel positioning jacks Each jack includes 2 x 75mm standard castors, 2 x 75mm castors with locking brakes Steel construction Easily move cars backwards, forwards, even sideways Steel construction for strength and durability Heavy duty swivel castors Locate underneath vehicle wheels allowing precise and easy movement within confined spaces Grooved, treadplate surface that can handle up to a 680kg load per jack Working Load Limit: 680kg per Dolly Total capacity is 1360kg for the set of 2 Each jack includes 2 x 75mm standard castors and 2 x 75mm castors with locking brakes Dimensions (L x W): 400mm x 300mm Weight: 15kg.  FINAL DETAILS | - Car is currently stored on a RESIDENTIAL property in Cranbourne, Melbourne, VICTORIA (3977) - If this ad is up then the car is still available for sale - Car is advertised on multiple sources - SOLD AS IS. Happy to assist preparing the car for pick up (eg strapping everything down) - FREE BONUS INCLUSION: 4 x 1360kg wheel dollies / positioning jacks with 75mm castors and locking brakes worth over $300.00 - FREE BONUS INCLUSION: plastic basic car creeper - FREE BONUS INCLUSION: car cover - Engine is seated in engine bay on stock engine mounts without being bolted in - All fluids have been kept in (eg engine oil, transmission oil, diff oil) during storage but recommend inspection and service before attempting to start - Inspections welcome on weekends Saturday and Sunday ONLY with prior arrangement - Pick up on weekends Saturday and Sunday ONLY with prior arrangement - If tow truck is being organised weekday pickup may be negotiated and arranged - Interstate buyers welcome, happy to organise video inspection if requested - Additional images (128) have been taken and can be provided to people with serious interest on request - Full payment expected before car would be released - Any questions I will try my best to answer to my knowledge. Price: AUD $18,000.00 Payment: Cash or transfer (preferred) Contact via email: [email protected].